How To Remove Plasti Dip From Rims
Plasti Dip is a great way to add flair to your car. However, when you decide that you no longer want it on your rims, removing it can be a bit tricky. The process of removing the dip from the rims may seem tedious and time-consuming.
What Is A Plasti Dip
Plasti Dip is an innovation of rubber coating, primarily used in insulating handles and knobs of electrical equipment. It is an elastic and waterproof insulating compound which dries out quickly and does not crack or become yellow. The Plasti Dip creates a film on all smooth surfaces such as plastic, metal, rubber, vinyl, leather, and many more.
If you are applying Plasti Dip on your rims for the first time, always do a test run on a less visible area such as your bumpers or side mirror. Once you are sure about the appearance, you can go ahead and apply it on your rims without any hesitation.
How Long Does A Plasti Dip Usually Last
This rubber coat has very low durability and can easily remove with a combination of different solvents. It is not advisable to use gasoline or thinner because that will cause damage to your paintwork.
Different Ways Of Removing Plasti Dip From Your Rims
Plasti dip forms a thick layer, making it difficult for you to remove it using water or soap and water. However, there are several ways you can use to remove it from your rims.
1) Using Spray Cleaner
A straightforward way to remove plasti dip is by using an aerosol spray cleaner widely available in automotive stores. Simply spray the cleaner on a sponge or a soft cloth and start scrubbing the dip on your rims. You can use a circular motion or merely rub it using pressure to remove the dip altogether from your rims.
2) Using Acetone-Based Nail Polish Remover
You can also try acetone-based nail polish remover to remove the Plasti Dip off your rims if the spray cleaner does not work. Apply a generous amount of acetone-based nail polish remover on the rims and leave it for about 10 minutes. Use a clean cloth or sponge and start scrubbing using circular motions.
3) Using WD-40 Or Kerosene To Remove The Dip From Your Rims
These two liquids are pretty popular forCanremoving paint, varnish, and other gum-based substances. Spray or pour some WD40 or kerosene all over the dip on your rims. Let it stay for about 10 minutes, and start scrubbing using a wire brush.
4) Using A Power Washer To Remove The Dip From Your Rims
This is one of the best ways to remove the Plasti Dip from your rims. You can use a power washer or simply soak your rims in warm soapy water and let it stay for about 10 minutes. The soap solution will help soften the plasti dip while the power washer will blast it off.
5) Using A Heat Gun To Remove The Dip From Your Rims
A heat gun can effectively remove the plasti dip from even the most challenging surfaces. It makes the surface soft and easy to scrape off by using a wire brush. However, you must be very careful while using this method because it may damage your paintwork or rims if used for a long time.
6) Using Acetone To Remove The Dip From Your Rims
You can also use acetone to remove plasti dip from your rims, but this method is only recommended for experienced car owners. Dab some acetone on a clean cloth and wrap it around the area where you want to remove the dip. Use a hairdryer to heat the acetone and soften the plasti dip. Now, start peeling it off using a wire brush or your fingers.
7) Using A Heat Gun And Nail Polish Remover To Remove The Dip From Your Rims
This is another case where two liquids can be used together to remove the plasti dip from your rims. However, you need to be very careful while using this method because the combination of heat guns and nail polish remover is not meant for beginners.
Start by applying some nail polish remover on a clean cloth or sponge and then heating it with the help of a heat gun. Now start scrubbing the heated area using circular motions or simply rub it off using pressure.
8) Using A Cleaner And Fine Grit Sandpaper To Remove The Dip From Your Rims
This is one of the best ways to remove plasti dip from your rims because you will not need any additional chemicals to carry out this process. However, if you are unsure or if the spray cleaner does not work, you about it, or do not have the required tools for this method, make sure you only use fine-grit sandpaper.
You can purchase a cleaner from an automotive store which will help remove the plasti dip more easily. Simply dampen a clean cloth with the cleaner and start scrubbing your rims with fine sandpaper.
9) Using Goo Gone And A Scouring Pad To Remove The Dip
This is another everyday method users follow when they want to remove plasti dip from their rims. All you need to do is apply some goo gone on a clean cloth or sponge and start scrubbing your rims using circular motions. Use a scouring pad and keep washing the rims for about 15 minutes.
What To Do After Cleaning And Drying Your Rim With Any Of The Above Methods
After you remove the Plasti Dip from your rims, make sure you clean and dry them thoroughly. Then, apply a liquid wax or rubber coating on the surface to protect it from getting damaged by other substances in the future. You can also use protective spray paint if you want to repaint the area.
It is difficult to carry out plasti dip removal from your rims, but it is still possible. You need to follow the mentioned methods and apply a little patience while carrying out this task. If you have any questions about removing Plasti Dip from your rims, feel free to ask us using the comments section below. We would love to help you out.
Q: What is rubber coating, and how effective is it as a plasti dip remover?
A: Rubber coating may work as an effective Plasti Dip remover, but the user must be very careful while using this method. It can quickly damage your rims if you do not apply it properly, so make sure you take help from an expert and use rubber coating as a last resort.
Q: What is the best way to remove Plasti Dip from your rim without damaging it?
A: There are many efficient ways to remove Plasti Dip from your rims, but we recommend using heat guns and abrasive sponges/brushes as they do not damage your edges in any way.
If the spray cleaner does not work, you: You can either use heat guns or acetone to remove the dip from your hubcaps. First, apply some acetone to a cloth and start scrubbing the surface with it. This will help you remove the thin layer of the dip easily.